|
|
| Microprocessor
based oil test set
|
|
Features :
×
Microprocessor controlled, fully automatic test sequence,
saves operator's time.
×
International specifications for testing insulating oil selectable form
pre- programmed menu.
×
Operator defined test program facility gives wide choice of test
parameters, viz, intermediate stand time and number of tests.
×
" Quick test and Proof test" facilities etc.
×
Recall of individual tests including breakdown voltages, averages,
and the test number, all displayed digitally.
×
Emergency exit allows the operator to quit the process.
×
Safety interlock on high voltage test chamber and zero start.
×
The sets are available with printer port and / or RS232 interface.
×
Equipment to enable easy, accurate and safe measurements
|
Application :
Theses test sets are used for determining the di-electric BDV of insulating
oils, both new and in-service ones, used in transformers, switchgear and other
electrical equipments. They are suitable for field or laboratory use and will
test oil to many international specification.
Function :
× Our instrument has advanced functions for
fully automatic tests. They enable the operator to simply prepare an oil test
cell, load it with sample oil, place it in the chamber and initiate the test
sequence. The test set carries out, automatically (and if necessary unattended),
the series of tests as defined by the selected oil test specification. On
completion of a test sequence the average break down voltage value is displayed
and the value for each individual test may be recalled.
× "Initial wait time, rate of rise of
test voltage, intermediate stir time, settling time and number of
tests" : According to many oil tests, specifications are all
pre-programmed into the sequence itself and kept the test program
parameters stored in memory for use when required even after power
shut down. A quick five-minute test sequence is available for rapid
assessment of the condition of a sample.
× "Proof Test" on oil sample can
also be performed. These tests allow the operator to raise the test
voltage to the level the operator chooses and retains it there for a
maximum of a minute to see and increases until a breakdown occurs.
|
Sr
no. |
Test
code |
Initial
Stand Time (Sec.) |
Rate
of rise of
test volt.(Kv/Sec) |
Inter
Mediate
Stir (Sec.) |
Inter
Mediate
Stir (sec) |
No.
of Tests. |
Remarks. |
| 1. |
5
Min
: Test |
60 |
2 |
30 |
30 |
3 |
Tests
till breakdown |
| 2. |
ASTM
: D877 |
140 |
3 |
- |
60 |
5 |
-Do- |
| 3. |
ASTM
: D1816 |
180 |
0.5 |
Continuous
Stir |
60 |
5 |
-Do- |
| 4. |
IEC
156 |
180 |
2 |
60 |
60 |
6 |
-Do- |
| 5. |
ISS
6792 |
600 |
2 |
60 |
300 |
6 |
-Do- |
| 6. |
Custom
Test |
0-5994 |
0.5
to 3 |
0-5999 |
0-5999 |
1-888 |
-Do- |
| 7. |
Proof
Test "A" |
Voltage
rise at 2Kv/second to user preset value, maintained there for one
minute where upon voltage is removed unless breakdown occurs. |
| 8. |
Proof
Test "B" |
Voltage
rises at 2Kv/second to user preset value, maintained there for one
minute where then rises at 2Kv/second to maximum unless breakdown
occurs earlier. |
BRIEF SPECIFICATIONS :
|
Output Voltage |
: |
0 - 60Kv or 0 - 80Kv or 0 -
100Kv variable (Any one). |
|
Supply Voltage |
: |
230V AC : 50H, 1Phase. |
|
Metering
& Display |
: |
Digital Kv meter to read 0 to 100Kv test voltage. The LCD
display unit will indicate all the parameters one after another as per the
program |
|
Stirrer |
: |
A magnetic stirrer is provided in the
instruments |
|
Protection |
: |
a) Fuse
b) An electric circuit to trip the instrument when the
leakage current through the oil under test will exceed the preset limit |
|
Safety Arrangement |
: |
a) Zero start interlock.
b) Oil chamber door interlock.
c) Low level, high level interlock for motor.
d) Fast acting electronics type
current sensing circuit in the event of insulation failure of the oil under
test.
e) Facility to quit the process any time |
|
Cabinet |
: |
Powder coated sheet
metal cabinet |
|
Optional |
: |
RS 232 computer
interface |
|
Printer output |
: |
Printer
Port for connecting 80 column dot matrix printer |
|
Standard Accessories |
: |
a)
Mains cord, detachable, 1.5mtr.long.
b) Oil test cell with electrodes.
c)
Electrode spacing gauges 'GO and NOGO'.
d) Operating instruction manual. |
|
|
